![]() ![]() If the problem persists, seek assistance from an engineer. Check the connections between the additional units. Try turning the printer off and on or reseating the DIMMs formatter board.Īn additional paper or envelope tray has caused a problem. controller, improperly fitted or bad firmware DIMMs or defective formatter board have been detected. Reseating the memory chips or replacing the formatter board should resolve this.Įither a defective D.C. Check there are no obstructions such as staples or paperclips.Ī defective formatter board or bad memory SIMMs has been detected. Reseat or change the memory to resolve.Ĭommonly associated with newer models, this error code indicates a problem with the motorised tray lift. This error code may arise as a result of an issue with an environmental sensor, memory controller, fan, power or DC controller.Ī motor error has occurred relating to either the main motor, fuser motor, image drum motor or ETC motor. One or more of the fans on your HP printer have failed. ![]() In this instance contact an HP engineer.ĭepending on the model of HP printer, this printer device error can be resolved in a number of ways including: making sure the paper tray is correctly installed, reinstalling the stacker, making sure you're not incorrectly printing through the duplex unit, duplex mode isn't enabled when printing envelopes, the printer configuration is correct. This code indicates there is a poor connection between the DC controller and the formatter. The sealing tape may not have been removed from your cartridge causing an error with the printer cycle. To be solved by an HP engineer, this fault indicates an error with the polygon mirror used during the scanning process. It could also be a problem with the scanner unit on your model. Most often associated with older printer models, this code indicates that the tab on the bottom of a cartridge has been broken off and/or is missing. There has been a high fuser temperature detected. Through possible overheating, the fuser heater has cut-off.Ī problem with the fuser drive motor has occurred which has then caused a fuser pressure release mechanism failure.Ī fault with the secondary thermistor has been detected. Your printer has detected the wrong type of fuser. Potentially caused by a bad mains supply, the fuser has become faulty. There has been a warm-up failure or the period allocated for the warm-up period has timed out.Ī high temperature has caused the thermistor to become too hot. There is an issue with the fuser caused by a low temperature and the fuser failing to warm up. Try updating the firmware and restarting the printer, if still unresolved it may mean a hardware issue. Simply turn the printer off at the plug for a minute before resuming your printing.ĭepending on your HP printer, this can be caused by a number of issues associated with the firmware. Check your connection settings as well as all cable connections.Ī temporary print engine error has occurred. The hard disk drive in your printer has crashed and you should resolve this by pressing the 'select' button on your machine.Ī data transfer error has caused the connection between your printer and computer to break. PostScript firmware errors will cause this code to appear, try printing an alternative PostScript file or reseat the PostScript SIMM. ![]() This code will appear should you send too many print jobs to the printer. ![]() Try connecting via a different method and that the cable is connected at both ends. The printer and your computer or having a communication problem. Reducing the DPI or making the document simpler are just a couple of steps you can take. If a print job exceeds the memory capacity of the printer, this code will appear. This is a warning that your toner levels are low or empty. Remove and reinstall to resolve the problem. The printer doesn't recognise your cartridges. Don't risk damaging the machine to remove a paper jam. Indicating a paper jam, this code can be removed by following the guidance on the printer screen. If this code appears, check whether your cartridges are correctly installed and that the cover is not open. Your printer is out of paper and so you should add sheets to the paper tray. If these fail, it could be a hardware issue. Try resetting the printer initially and reinstall the toner cartridge if the problem persists. A hardware problem may be the reason the error message persists.Īlso known as "Supplies Memory Error", this code indicates that the machine is having difficulty with a toner cartridge chip in that it's unable to read it. An issue most commonly associated with driver or printer cable problems, turning the printer off and on should see this error message disappear. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |